Measure. Save. Prove.
Most plants buy equipment first and measure never. We do it the other way round, and we keep measuring after the equipment goes in.
iSAVE is the measurement layer of the Karnot platform. It goes in before anything else, so every heat pump, solar array, CO₂ refrigeration plant or energy store we propose is sized against your real load, not a nameplate. It stays in afterwards, so the saving is proven on the same meters every month.
Measure
A licensed electrician clamps sensors on the incoming supply and the feeders that matter: chillers, compressors, boilers, hot water, air handling, process lines. About three weeks of data, watched live from day one.
- The 15-minute peak that sets your demand charge, and the machine that caused it
- Power factor, so you know if a surcharge is hiding in your bill
- Night and weekend base load: the kilowatts running for nobody
- Your real heating and cooling load, hour by hour
Save
The data says what to fix and in what order. Then the rest of the platform does the work.
Prove
The same meters stay in. Every month you get the bill-before, the bill-after and the difference, in kWh, pesos and tonnes of CO₂.
- Baseline and savings calculated to the IPMVP method banks accept
- Scope 1 and Scope 2 figures in the form your SEC sustainability report needs
- A verified record of each cut, the raw material the new national carbon registry is built to hold
- Alerts when a machine drifts back to old habits
From the incoming supply down to each machine
One logger, one timeline, every utility on site. Add channels as you go; nothing is ripped out.
Incoming supply
Flexible coils wrap around busbars and main feeders up to 10,000 A. Voltage, current, kW, kVA, kWh and power factor on all three phases.
Sub-circuits and machines
Clamp-on sensors from 50 A to 400 A on the feeders that matter. See each chiller, compressor, boiler, oven, pump and air handler on its own line.
Gas, diesel and water
Pulse inputs read fuel and water meters on the same timeline as the electricity, so a boiler's true cost per litre of hot water is a fact, not an estimate.
Meters you already own
Existing electricity meters with a Modbus port are read directly. Temperatures, tank levels and run signals come in through the input module.
Power quality
Harmonics against the IEEE 519 limit, voltage sags and swells, and the reactive power your electricity provider surcharges. Names the load doing the damage.
Control, when the data says so
The output module switches loads, holds a demand limit, times EV charging and tells storage when to discharge. Measurement first, control second.
How it goes in
A few hours in the switchroom. No new cabling across the plant, no change to your IT network.
Walk the switchroom
Our engineer lists the feeders worth watching and the meters already there. You get a scope on one page.
Clamp on
Sensors clip around live cables; coils wrap around busbars. The logger sits in a DIN-rail enclosure and talks over its own 4G link or your LAN.
Watch it live
Dashboard on your phone and desktop from day one. If the link drops, the logger keeps recording and catches up.
Read the report
After about three weeks: what you use, when, where, and what each fix is worth in pesos. Keep the kit and the proof continues.
What you get
Numbers you can take to the board, the bank and the auditor.
The survey report
One document, priced in pesos.
- Load profile for every feeder measured, hour by hour
- The month's demand peaks, time-stamped, traced to the machine that caused them
- Power factor and harmonics, with the surcharge and damage they cost you
- Base load that runs for nobody, and what switching it off is worth
- Heating and cooling load map, so a heat pump or chiller is sized to measured data
- The three largest savings, each with a peso figure and a payback
The ongoing proof
Every month, for as long as the kit stays in.
- Bill-before, bill-after, difference, in kWh, pesos and tonnes
- IPMVP baseline adjusted for production and weather, the method banks and ESCO contracts accept
- Scope 1 and Scope 2 figures ready for the SEC sustainability report
- Live data to your own BMS or software over MQTT, Modbus or API
- One site or your whole portfolio on one screen
- Alerts when a load drifts, a capacitor bank fails or a machine runs out of hours
Built for Philippine plants
The same logger works on a 50 A sub-circuit and a 10,000 A busbar. It has been specified for the sites below, and it pays for itself fastest where the bill is biggest.
Food and beverage plants
Boilers, CIP hot water, blast chillers and compressors on one timeline. Find the shift that sets the demand charge.
Cold stores and logistics
Compressor racks, defrost cycles and door losses, measured. Know what a CO₂ system would do to the bill before you buy it.
Hotels, resorts and hospitals
Hot water, laundry, kitchens and chillers against occupancy. The report tells you the cost per room-night, in pesos.
Frequently Asked Questions
Do we have to shut the plant down to install iSAVE?
No for most feeders. The sensors clamp around the cable; flexible coils wrap around busbars and large feeders. A licensed electrician fits them in the switchroom in a few hours. A shutdown is only needed where the panel layout leaves no safe access.
Can iSAVE read the meters we already have?
Yes. Existing electricity meters with a Modbus port are read directly. Gas, diesel and water meters with a pulse output connect to the same logger, so the whole site is on one timeline.
Does iSAVE need our internet or IT network?
No. The logger ships with its own 4G link, so nothing touches your network. If you prefer your own LAN, it uses that instead. If the link drops, it keeps logging and catches up when the link returns.
Is iSAVE a survey or a permanent installation?
Both. A survey runs about three weeks on the same equipment. If you go ahead with the fixes, the equipment stays and the same meters prove the saving every month.
Does iSAVE control equipment, or only measure it?
Both. The output module can switch loads, hold a demand limit, time EV charging and tell storage when to discharge. Control is added only after the measurement shows what it should do.